AISI S213-07-S1-09 PDF

AISI S/S (). DISCLAIMER The material contained herein has been developed by the American Iron and Steel Institute Committee on Framing. AISI S / S () North American standard for cold-formed steel framing – Lateral design,. edition reaffirmed Not for loan. AISI S North American Standard for Cold-Formed Steel Design, Edition (Reaffirmed ); AISI S w/ S (): North.

Author: Nikora Male
Country: Trinidad & Tobago
Language: English (Spanish)
Genre: Photos
Published (Last): 22 May 2016
Pages: 118
PDF File Size: 5.71 Mb
ePub File Size: 6.68 Mb
ISBN: 501-6-36376-542-4
Downloads: 52863
Price: Free* [*Free Regsitration Required]
Uploader: Shazshura

In the case of a coldformed steel framed shear wall, the SFRS elements include the chord studs, intermediate studs, hold-down anchors, track, etc. A summary of the test program is provided, including design approach, failure e and ductility measures. For intermediate values of opening height ratio and percentages of full-height sheathing, the shear resistance adjustment iasi shall be permitted to be determined by interpolation.

The Rd value was reduced for the situation where gypsum sheathing is relied upon in seismic design to account for the decreased ductility of the system, similar to the NBCC listing for wood framed walls with gypsum panels.

Free CFS Publications from the AISI/SMDI Construction Market Council –

s213-07s-1-09 Since the shear wall tests were carried out over a short time span, the tabulated values are for short-term duration loads, including xisi and earthquake.

Because steel is not affected by splitting or tearing when fasteners are closely spaced, no reduction in the calculated strength was taken for closely spaced fasteners. Foundations shall be designed ais resist the loads resulting from the lesser of the loads that the system sisi deliver C5.

Asclepius, Commentary on Nicomachus. If a Capacity Based Design approach is not implemented, then the ductility of the wall may be reduced due asi failure of aisk or a number of other elements in the SFRS. The design of diaphragms that resist wind, seismic or other in-plane lateral loads shall comply with the requirements of this section. Shear values are permitted for use in seismic design where the seismic response modification factor, R, is taken equal to or less than 3, subject to the limitations in Section C1.

When the seismic response modification coefficient, R, is greater than 3, AISI S requires that the design zisi follow the special seismic requirements of Section C5 and when R is less than or equal to 3, Section C5 is not required.

TOP 10 Related  HEALTH UARK EDU FORMS IMMUNIZATIONCOMPLIANCE PDF

If the load combinations for Allowable Stress Design ASD with the system overstrength factor are desired to be used and they are to be checked against the member nominal strength, then member nominal strength is required to be divided by 1.

Structural panels shall be permitted to be applied either parallel to or perpendicular to framing. The eccentric effect due to single sided bracing is neglected for purposes of this classification, but shall be considered in sisi with C5. Unless otherwise noted, all sheathing edges shall be attached to framing members or blocking. The connection of the diagonal strap bracing member shall be welded and designed to permit gross cross section yielding of the diagonal strap bracing member, unless one of the following criteria is satisfied for the aidi connection: Therefore, for thinner sheet steel, the limit state would likely be the tilting and bearing failure mode.

This can be achieved by applying an overstrength factor to the nominal resistance Figure C Note that the lower RdRo value of 1.

For wood structural panel sheathed shear walls, tabulated Rn values applicable for aisk load duration seismic loads. Hikita verified that shear walls subjected to combined gravity and lateral loads can perform at an adequate level to warrant the use of the tabulated Rd and Ro values, if the chord studs are designed to carry the anticipated compression force, related to sheathing connection failure s23-07-s1-09 a seismic event, combined with the associated NBCC principal and companion gravity loads.

Aisk this blog was made to help people to easily download or read PDF files.

Indeed, in many jurisdictions, such review is required by law. Lateral system not specifically detailed ausi ductile seismic performance Capacity based design approach not required. The design of cold-formed steel members to support the additional mass of concrete and masonry elements needs to be in accordance with AISI S [CSA S] and required deflection limits as specified in concrete or masonry standards or the model building codes.

Fiberboard shall be applied perpendicular to s213-07-ss1-09 with strap blocking behind the horizontal joint and with solid blocking between the first two end studs, at each end of the wall, or applied vertically with all edges attached to framing members. Unblocked assemblies shall be permitted provided the nominal resistance values above are multiplied by 0.

Free CFS Publications from the AISI/SMDI Construction Market Council

An individual sample may include several thicknesses for a given sample grade and coating. Alternatively, for diaphragms sheathed with wood structural panels, the available strength may be determined by the section D2.

TOP 10 Related  EL REALISMO JURIDICO ESCANDINAVO UNA TEORIA EMPIRISTA DEL DERECHO PDF

The nominal strength [nominal resistance] so calculated defines the maximum resistance that aiwi diaphragm, shear wall, or diagonal strap bracing is capable of developing. The basic s21-07-s1-09 cyclic test protocol used in the tests is illustrated in Figure C Al-Kharat and Rogers showed through testing of double sided strap braced walls that the R values used for conventional construction CC in CSA S16S1 could also be applied for coldformed steel systems that had not been designed with a capacity based approach.

When R is less than or equal to 3, Section D3 is not required. The strap braces were expected to undergo gross cross-section yielding along their length, while the other elements in the seismic force resisting system SFRS were selected to be able to carry the probable brace capacity. The Committee has made a diligent effort to present accurate, reliable, and useful information on cold-formed s framing design and installation.

Capacity based design approach is applied, assuming the sheathing connections act as the energy-dissipating element See Section C5.

Fiberboard panels shall comply with AHA A Upanishad Commentary Full Eng commentary on the vedanta and upanishads to get a insight to profound knowledge of vedic seers. Standard Language and Poetic Language Analysis of ss between standard language and poetic language. Serrette conducted tests on cold-formed steel frame shear walls utilizing structural adhesives.

The probable capacity is only used to estimate the forces in the design of the non-fuse elements of the SFRS.

RdRo is taken equal to or less than 2 for sheathed shear walls, and equal to or less than 1. Blocked Unblocked Screw spacing at diaphragm boundary edges and at all continuous panel edges in. For Seismic Design Category A through C, aissi designer has the option to use an R of 3 for systems with a higher assigned R to determine the seismic load and thereby avoid the special detailing in S123-07-s1-09 C5.

If either Ry or Rt is determined by test, then both Ry and Rt must be a test value.