The Uniden Bearcat BCT15X is the follow-up to Uniden’s premier analog mobile scanner, the manual for the radio is contained on a CD-ROM, in PDF format. DImage_/Manual/ (1 of 3)5/26/ .. This page applies to the following scanner(s): BCDXT BCT15X Uniden® and Bearcat® are registered trademarks of Uniden America Corporation. View and Download Uniden BCT15 owner’s manual online. scanner radio with You can adjust the level of the following tones: Key Beep, BearTracker Alert.
|Published (Last):||20 November 2012|
|PDF File Size:||9.8 Mb|
|ePub File Size:||18.14 Mb|
|Price:||Free* [*Free Regsitration Required]|
Set Modulation conventional only This setting selects the modulation used for the channel.
UNIDEN BCT15 OWNER’S MANUAL Pdf Download.
Priority for priority channels in the same channel group follows the order in which the channels were created. The BCT15 can search each of its 13 service search ranges and up to 10 custom search ranges to find active frequencies. This lets many users share a single frequency, and decreases interference caused by distant transmitters on the same channel.
Edit Name allows you to change the name of a group. To select a PIO turn the scroll control. LTR systems work a little differently. Enter the new frequency and press Hold. The search time changes depending on the search step size.
Then see Edit Site Options. Repeat for each block as needed and you will return to the ‘ Edit Sys Option ‘ menu. This deletes all programmed data. If a talk group you assign as priority is not also a priority channel on the transmitting system, then the scanner will use standard trunking priority for the talk group.
On – the scanner checks conventional priority channels. Fire Tone-Out will now search and find your tones to program duh.
Top Questions for Uniden BCT15X Scanner
The first time the scanner starts receiving a signal from the GPS, it beeps and briefly displays ‘ GPS Connected ‘ and temporary locks and unlocks all sites and groups that are ‘enabled for scan’, unlocked, and whose quick key is enabled according to your current location.
For example, the code for Tarrant County, Texas, is This is a system that automatically stores the frequencies found by Close Call. Page 6 Programming General Settings The default setting is Off. Lets you search and store frequencies from enabled custom search ranges or a service search range into a conventional system, or new talk group IDs into a trunked system. Those are covered below. Press to toggle selected State frequencies or Dept. Press MENU to save and exit.
Dynamically Allocated Channel Memory – organized into ‘Systems’, ‘Sites’, within trunking systems’Groups’ within systemsand channels within groups. In Tone-Out Standby Mode: These scanners will allow you to program just Motorola control channels into the trunking system and the voice channels will automatically be found but not programmed.
Uniden BCT15 Owner’s Manual
There are two ways to set Priority Scan. My advice is to disable everything and start from there. Using Bear Tracker Scanning. Type II IDs are identified by a 5-digit number.
Scroll to ‘ Disp. It is also recommended that you download and install the latest firmware upgrade for the scanners if you don’t have it. Program your talkgroups into channel groups within that system and all talkgroups in the system are available to every site so they don’t have to be reprogrammed for each site. Press then VOL State. Trunk Tracking Tone Volume Adjust — lets you select and set various tones for different purposes.
Marked Channel – The scanner only sends the audio bxt15x channels that have the record option turned on to the REC jack. bct15s
Set Attenuator to select to choose an attenuation for all frequencies in the range. All FIPS – the scanner sounds a weather alert siren for any programmed countythen opens the squelch and remains on the weather channel. Wired cloning between other models to the BCT15 is not possible. Quick Search lets you search from the bezrcat frequency if you are scanning, or enter a frequency to start searching from.
Number of Talkgroups per Block. Scanning- the process of stepping through conventional channels in groups, which are in programmed ‘systems’.
You must use either the supplied antenna or an electrically correct outdoor antenna, properly manyal safely mounted at your chosen site. The display will show the Tone-Out name, channel numberand tone settings.
Adjusting the Display Contrast this setting controls the display’s contrast how light or dark it appears. Stores location and range. No] then both digits.