Default Re: Huawei CDMA E BTS Max Power??? HI I think it can be more than 20W because the RF board support MAX 60W. The 3rd Global CDMA Operation and Development Forum, themed. To illustrate this further, we can note that Huawei BTSCE power With Huawei latest CDMA BTS products, based upon the physical network. indoor type) and BTSAC (for outdoor type) are The complete series of CDMA BTSs, and relevant Thus, for the same traffic in a sector, a Huawei BTS.

Author: Tutaxe Tojajind
Country: Central African Republic
Language: English (Spanish)
Genre: Health and Food
Published (Last): 13 January 2018
Pages: 488
PDF File Size: 1.5 Mb
ePub File Size: 15.98 Mb
ISBN: 620-5-41526-702-4
Downloads: 14841
Price: Free* [*Free Regsitration Required]
Uploader: Fenrigore

CDMA grows greener

Conducting Insulation Test To conduct an insulation test, proceed as follows: Tools The following tools are required: Indoor centralized rack icr dual-mode base station pages. Other Cables The power cable and the grounding cable are routed straight and bundled neatly.

The letters A, B, C as shown in Figure are not cable labels.

The alarm box is correctly installed according to the design. Route the alarm cables coming in from the other side of the enclosure through the cabling holes on both sides of the 8-E1 module and then to the respective slots. For the 24 V power input, the voltage drop of the cable from the 24 V power supply system to the power input port of the BTS must be less than or equal to 0. To locate the support at the side of antistatic floor, proceed as follows: Page 15 The packing case is in good condition.


Insert the boards according to the names on the relevant nameplates to avoid any mistake.

They are used for the convenience of installation description. Loosen the screw in the small round hole such as —48V connecting hole on the power input 33606 of the terminal block using a flat-head screwdriver. By pressing ‘print’ button you will print only current page. Do not bend an optical fiber to a right angle upon distribution. Diagonally fasten them to a 45 N-m in-lbas shown in Figure Administration Building, Huawei Technologies Co.

Huawei CDMA E BTS Max Power ???

Procedure To prepare power cables, huawsi as follows O 2 Configuration The O 2 refers to an omni cell with two carriers. Figure shows RF cable connections, indicated by blue lines. Note, Comment, Tip, Knowhow, Thought: Remove four bolts and one gasket that connect the antistatic floor and the support. Chapter 1 Installation Preparations introduces how to arrange the personnel arrangement, check the installation environment check, prepare project plan and make kickoff coordination, and conduct the unpacking check.

Cut the tapes along the seams of the carton cover using a knife. Thus, you do not need to install these cables on site. Mouse btw Action Description Press and hold the primary mouse button left huawdi Select button by default. Procedure To carry out the power-on check hawei power module, proceed as follows: Figure Installing a board 2 Tighten the screws clockwise on the front panel, as shown in Figure Feed back the situation to the local Huawei Representative Office.


Connect one end of the cable to the working cdms of the EAC. If the power supply is on during the operation, do not touch the binding posts with the adjustable wrench or the screwdriver. Paint the whole support with rustproof coat and top-coat. To print the manual completely, please, download it. For the proper storage, use and disposal of this product, national laws and regulations must be observed. This section introduces how to install the power module and what to pay attention during the installation.

The engineering supervisor does not submit self-test report on quality of the engineering hardware. Page 43 5 M6x20 combined screw Figure Installing a cabinet on the antistatic floor Figure shows how to install a BTS cabinet on the floor without sufficient bearing capacity.

Page of 93 Go.